Posted in

What is the effect of viscosity on an OH2 Type Pump?

If you’ve ever worked with fluid transfer systems—whether in manufacturing, water treatment, or industrial processing—you’ve probably encountered an OH2 type pump before. For anyone in the game, this is a workhorse: a centrifugal end-suction pump, standardized to handle a huge range of non-corrosive, clean (and not-so-clean) liquids, built for durability and low maintenance. But here’s the thing I see all the time, even from seasoned operators: people treat viscosity like an afterthought when it comes to how this pump performs. And that’s a mistake. OH2 Type Pump

Let’s start with the basics that matter, not the textbook jargon. Viscosity, put simply, is how “thick” a liquid is. Water is super low viscosity—like, almost thin enough to run through a coffee filter. A heavy oil, say 10W-40 motor oil, is way higher viscosity; it oozes instead of pouring fast. When that liquid moves through an OH2 pump, that thickness directly changes how the pump runs, how much liquid it moves, and even how long its parts last. As an OH2 pump supplier, I’ve fielded hundreds of calls from guys who bought a pump for water, then tried to run maple syrup or industrial gear oil through it, and wondered why it’s suddenly sputtering or not pumping enough. That’s not a defect in the pump—it’s viscosity throwing its weight around.

First up: flow rate, which is basically how much liquid you get out of the pump in a minute. For an OH2 pump engineered for water, the performance curve (the thing that tells you flow at a given head, or pressure) is baked in for a low-viscosity liquid. Water’s viscosity is ~1 centipoise (cP) at room temp, right? That’s the baseline. When you bump viscosity up to, say, 500 cP—that’s like light paint, or mild syrup—flow rate drops fast. Here’s why: the impeller inside the pump spins to push liquid, but thick liquid resists that spin. It creates drag between the liquid molecules and between the liquid and the pump’s internal parts (like the casing and impeller vanes). That drag means the impeller can’t move as much liquid per revolution as it does with water. Run up to 1,000 cP (like heavy oil or molasses), and flow rate can drop by 20-30%—sometimes even more, depending on the pump’s size. I saw this last month with a customer who used a standard OH2-5 pump to pump a 700 cP industrial coolant; he was expecting 120 gallons per minute (GPM) and only got 85. That’s not the pump being broken—it’s viscosity doing its thing.

Then there’s head, which is the pressure the pump can generate to push liquid up or through a pipe. Again, baseline is water. For the same OH2 pump, head (measured in feet, usually) also takes a hit when viscosity rises. Why? Same drag issue, but amplified here. The impeller’s energy isn’t just moving liquid—it’s fighting that thick liquid’s resistance. So instead of building up pressure to push liquid 100 feet up, it might only push it 70 feet. I’ve seen some folks try to compensate by cranking up the motor speed, but that just wastes energy and puts extra stress on the pump’s bearings and seals. As a supplier, we always flag this: if you’re moving liquids over 200 cP, you need to tweak the pump’s specs, not just crank the speed.

Wait, but not all high viscosity is bad? No, but there’s a line where the OH2 pump stops working efficiently. The hydraulic efficiency of the pump—how much of the motor’s power actually goes into moving liquid instead of fighting drag—peaks right around 1 cP (water). By 100 cP, efficiency dips 10-15%. By 1,000 cP, it’s down to 50% or lower. That means you’re paying way more in electricity for way less output. A lot of operators don’t realize that: they see the pump turning on, so they think it’s working, but they’re throwing money down the drain (literally, sometimes, if the liquid doesn’t move fast enough).

Now, let’s talk about the parts of the pump, because viscosity isn’t just about numbers—it’s about wear and tear. That drag I mentioned? It’s also causing friction inside the pump. For low-viscosity liquids, the liquid actually lubricates the gap between the impeller and the pump casing, and between the shaft and the seals. But high-viscosity liquids? They don’t flow into those tiny gaps as easily. So instead of a thin, protective layer of liquid, you get metal-on-metal contact in spots. That speeds up wear on impellers, shafts, and mechanical seals. I had a customer a few years back who ran an OH2 pump for 6 months on 800 cP liquid; his mechanical seal failed twice in that time, whereas another guy running the same model on water went 3 years without a seal replacement. That’s viscosity killing parts faster, plain and simple.

But here’s the silver side: when viscosity is low, the OH2 pump performs exactly like it’s designed to. For water, thin chemicals, wastewater with small solids (as long as they’re not too big), the OH2’s end-suction design is perfect. It’s self-priming (well, mostly—some models need a priming port, but the standard ones are great for flooded suction), and it’s built to handle 1 cP liquids without the drag issues I’m talking about. That’s why so many municipalities use OH2 pumps for water distribution, or food plants use them for moving thin syrups (like simple syrup for soda) or cleaning solutions.

Wait, what about medium viscosity? Like, say, 100-200 cP, which is mild paint or crude oil. You can still use an OH2 pump, but you need to adjust a few things. First, check the pump’s impeller: closed impellers (the standard ones) work for low viscosity, but open or semi-open impellers can handle slightly higher viscosity better because they don’t trap as much liquid, reducing drag. Also, make sure the motor is sized for the extra load—when viscosity goes up, the pump needs more power to turn, so an under-sized motor will burn out fast. That’s another call I get all the time: someone bought the “standard” OH2 pump with a 5HP motor, tried to run it on 300 cP liquid, and the motor tripped on overload within 10 minutes.

Here’s a common mistake I see even with experienced operators: confusing viscosity with specific gravity. They’ll say, “This liquid is heavy, so it’s high viscosity,” and that’s not right. Specific gravity is weight (water is 1 SG, motor oil is ~0.9 SG, so it’s lighter than water), but viscosity is thickness. A liquid can be heavy (high SG) and low viscosity, or light (low SG) and super thick (high viscosity). For example, glycerin is 1.26 SG (heavier than water) and ~1,490 cP (way thicker). So if you have a liquid that’s heavy but thin, the OH2 pump’s performance barely changes—just the motor’s power draw goes up a tiny bit. If it’s light and thick, that’s when you get the big drops in flow and efficiency.

Let me give a real example from our service logs to make this concrete. Last quarter, we sold three OH2-7 pumps (that’s a mid-sized model, ~200 GPM at 40 ft head for water) to a customer who runs a small manufacturing plant. They first used them to move deionized water, which is 1 cP—perfect, they got 195 GPM each, right on spec. Then they switched to a new cleaning solution that’s 450 cP (think, like, thick dish soap). Suddenly, their flow dropped to 138 GPM—almost 30% less. They called me panicking, thinking the pumps were defective. I walked them through checking viscosity (they had a cheap viscometer on hand, which I recommend every pump owner get) and realized the problem was the liquid, not the pump. We swapped them for a slightly larger OH2-8 pump, adjusted the impeller to a semi-open design, and within a week they were back to 180 GPM—only a small drop from the original water flow, but way better than what they had. That’s the kind of on-the-ground stuff that doesn’t show up in textbooks, but it’s exactly why as an OH2 pump supplier, we don’t just sell pumps—we help you match the pump to your liquid, including accounting for viscosity.

Another thing to note: viscosity changes with temperature. That’s a big one I almost forgot. If your liquid heats up, viscosity drops. If it cools down, it gets thicker. So if you’re moving a liquid that changes temperature a lot (like a hot cleaning solution that cools as it moves through the pipe), your pump’s performance will shift too. For example, heating that 450 cP cleaning solution to 120°F cuts its viscosity in half, to ~225 cP. Run that through the same OH2-7 pump, and flow jumps back up to 165 GPM, instead of 138. That’s a cheap fix if you have control over the liquid’s temperature—just heat it a bit, and you get better pump performance without buying a whole new unit.

Now, when is viscosity a dealbreaker for an OH2 pump? If you’re moving liquids over 1,500 cP—like heavy gear oil, molasses, or tar—you’re pushing the OH2’s limits. At that point, even the best-adjusted OH2 pump will have efficiency under 40%, and wear will be way too high. For those, you’d need a different type of pump, like a rotary lobe or gear pump, which are designed for high viscosity. I always tell customers: don’t force an OH2 pump past 1,000 cP, max. If you’re over that, we can point you to the right pump for the job.

Let’s wrap this up for anyone who’s just trying to make their OH2 pump work right. The takeaway? Viscosity isn’t a minor detail—it’s one of the first things to check when your pump isn’t performing as expected. It changes flow rate, head, efficiency, and how fast your pump parts wear out. For low-viscosity liquids (1-200 cP, like water, thin chemicals, simple syrups), your standard OH2 pump will work like a charm. For medium viscosity (200-1,000 cP), you just need to tweak a few things: check impeller type, make sure your motor is sized right, and consider heating the liquid if temperature is an option. For high viscosity over 1,000 cP, an OH2 pump isn’t the best fit.

If you’re not sure where to start, or you’ve got an OH2 pump that’s acting up because of the liquid you’re moving, we’re here to help. We don’t just sell pumps—we’ve got the service and expertise to walk you through viscosity checks, recommend adjustments, or find the right OH2 model for your specific fluid. Don’t let a viscosity mix-up cost you in wasted energy, broken parts, or lost production. Reach out to connect for a quick consult, and we can get your pump running at peak efficiency.

Vertical Slurry Pump References
Karassik, I. J., et al. Pump Handbook, 5th ed. McGraw-Hill, 2020.
Grundfos. Centrifugal Pump Performance for Viscous Liquids. Grundfos Technical Note, 2022.
Hydraulic Institute. Centrifugal Pump Standard ANSI/HI 9.6.1 for Viscous Flow, 2021.


Hebei Tongda Pump Co., Ltd.
Hebei Tongda Pump Co., Ltd. is well-known as one of the leading oh2 type pump manufacturers and suppliers in China. Our factory offers high quality oh2 type pump made in China with competitive price. Welcome to contact us for pricelist.
Address: No.158, Bo Ming Xi Lu, Boye County, Baoding City, Hebei Province
E-mail: wendy@hbtdby.com
WebSite: https://www.waterpumpmanufacturer.com/